Formlabs Fuse Blast

Product no.: FS1-FB-01

Fuse Blast delivers 100% hands-off cleaning and polishing for SLS parts

Achieve professional, consistent parts that are clean to the touch faster and easier than ever before with Fuse Blast, an easy-to-use, fully automated cleaning and polishing solution for post-processing SLS 3D printed parts.

Fuse Blast seamlessly integrates into the Fuse Series ecosystem and streamlines your post-processing workflow, empowering you to fully clean a whole build chamber of printed parts in as little as 15 minutes and drastically reducing labor time and cost. With the optional Polishing System, Fuse Blast takes your parts to another level by polishing them to a smooth, semi-gloss, and dye-ready surface finish, to deliver consistent, professional-grade results every time.

Finished Parts In 15 Minutes

Cleaning routines automatically post-process an entire build chamber in as little as 15 minutes, while the passive filtering reduces media saturation and extends media life to save on overhead costs.

Consistent Results

Pre-programmed routines take out the guesswork for consistent results, while manual mode allows you to adapt to any part requirements.

Professional Parts

Deliver clean-to-the-touch parts thanks to the in-line ionizer that prevents dust and media from re-settling on your parts, or go the extra mile with the optional polishing function for a smooth, semi-gloss, and dye-ready surface finish.

Streamlined Post-Processing

Fuse Blast seamlessly integrates into the Fuse ecosystem for an automated post-processing workflow that reduces labor time by 80% and delivers finished parts in as little as 15 minutes.


Fuse Blast is a fast, automated solution that delivers professional results, consistently.

  • Hands-off post-processing
  • Passive recycling for extended media life and faster processing on Sift
  • Pre-programmed routines
  • Add-on polishing upgrade*
  • In-line ionizer for clean-to-the-touch parts
  • Dual-function blasting with automatic or manual cleaning
  • Fully sealed and workshop-friendly operation


  • Printer Compatibility: Fuse Series SLS 3D Printers, Third-party powder bed fusion 3D printers
  • Minimum Dimensions for Convenient Access (W × D × H): 145 × 150 × 175 cm
  • Dimensions (W x D x H): 100 × 75 × 175 cm
  • Height when open: 195cm
  • Weight: 164 kg (without blasting media)
  • Media Hopper Capacity: 8.3 L, equivalent to 13 kg of 200-300 µm glass media
  • Waste Hopper Capacity: 10.6 L
  • Operating Environment: 10–36 ºC, Elevation up to 2286 meters
  • Air Handling: Negatively pressurized hood with replaceable HEPA filter, Independent venting system
  • Power Requirements: 230 VAC, 3 A (no dedicated circuit or vacuum required)
  • Compressed Air Requirements: Supply at least 10 SCFM at 90 PSI / 285 SLPM at 6 bar. Regulate pressure input between 90-120 PSI / 6-8 bar. Typically achieved by a single 4 HP compressor.
  • Connectivity: Wi-Fi: 2.4 GHz. Ethernet: 1000 Mbit. USB: 2.0
  • Wi-Fi Connectivity Protocol: IEEE 802.11 b/g/n Frequency: 2.4 / 5.0 GHz. Supported security: WPA/WPA2
  • Ethernet Connectivity: RJ-45 Ethernet (10BASE-T/100BASE-TX/1000BASE-T) LAN port. Connect with a shielded Ethernet cable (not included): minimum Cat5, or Cat5e or Cat6 for 1000BASE-T.
  • USB Connectivity: USB (rev 2.0) C port with a USB A-C or C-C cable
  • Sound Emission: Does not exceed 70 dB(A).
  • Product Control: Interactive touchscreen, foot pedals for manual control.
  • Included Accessories: Transfer container, Control pedals, ESD wrist strap, 7mm socket wrench, Blast orifice (3mm), Blast orifice (4mm), T-20 driver, Floor mat
  • Tumbling Basket: 450mm internal diameter (Fits a full Fuse build volume)
  • Internal work area (W x D x H): 71 x 55 x 67 cm
  • Accessible work area (W x D x H): 57 x 50 x 67 cm (basket removed)

Browse these categories as well: 3D Printers, Formlabs, Formlabs, Post Processing, Other Devices